Tech and Support for Diagnostic Tool
How to fix Carprog Clone LIB File Problem
Posted by OBD scanner

Here is the working solution on Carprog clone “LIB file problem” by re-flashing Mcu ARM AT91SAM7S256 step by step. ECU Programmer

Problem:
Any work solution for carprog v8.21 clone?
“Lib file problem. delete LIB file and make Update>-Internet”
 


Solution:
Yes, reprogram ARM with any jtag programmer.

Reflash Carprog MCU ARM by Jtag:
We need the stuff:
1- AT91SAM7S256.bin
2- Jtag programmer
3- Jtag software
We need to prepare the Carprog to connect to Jtag programmer but first the flash need to be erased, the Jtag function in mcu is disabled, you can’t connect to the mcu before erase the flash. Remove the AT88SC eeprom from the board, please note where is the pin 1 in eeprom before remove:
 


Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it with a small amount of silicone (you don’t want to broke the pin in the process).
Connect the Carprog (with the pin 55 disconnected) to the 12v supply, wait about 10 seconds and connect the wire from pin 55 to Vcc (3.3V) in Carprog:

 



Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect the 12v supply from CarProg full  and remove the pin 55 wire from vcc. The pin 55 must remain disconnected until the programming process is done.
Ok, that’s it. I make it; and you try on you risk.
Article from: http://carprog-carprog.blogspot.com/2016/10/how-to-fix-carprog-clone-lib-file.html

How to Cut TOY43 Key using Condor XC-Mini Find Bitting
Posted by OBD scanner

OBD2 engineer  teach you how to use Xhorse Condor XC-Mini cut keys if parts of the car are missing bitting on door lock/trunk lock/ignition lock.

 SEC-E9 Key Cutting Machine
Step1: Select Car information
Connected to the power supply, open Condor XC-MINI
Enter main interface, Click on ‘Find Bitting’
xhorse-condor-xc-mini-find-bitting-1
Select car maker ‘’Toyota’ Key cutter Machine
xhorse-condor-xc-mini-find-bitting-2
Enter ’TOY43’ and click on ‘Confirm’
xhorse-condor-xc-mini-find-bitting-3
Select key type and click on ‘Confirm’
xhorse-condor-xc-mini-find-bitting-4
Enter known bitting ‘23112134’
Enter unknown bitting as ‘?’
xhorse-condor-xc-mini-find-bitting-5
(Possible key bitting will be listed. Note that system has sorted the codes by the most
economical way in order to save blank keys. For example, the bitting under ‘First key’ only
needs three blank keys, the bitting under “Second Key” need another three blank keys, then the ‘third Key’…)

Step2: Prepare Key
Then push M1 clamp and tighten the clamp lock
xhorse-condor-xc-mini-find-bitting-6
Next put the blank TOY43 key on the M1 clamp and tighten it
xhorse-condor-xc-mini-find-bitting-7
Close the protective shield

Step3: Begin cutting
Click on ‘Find Bitting Code’
xhorse-condor-xc-mini-find-bitting-8
And click on ‘Cut’
xhorse-condor-xc-mini-find-bitting-9
It is processing…
xhorse-condor-xc-mini-find-bitting-10
Cutting complete!
xhorse-condor-xc-mini-find-bitting-11
You can clean up the clamp, probe and the cutter using the brush.

Article from: http://chasencai.over-blog.com/2018/06/how-to-cut-toy43-key-using-condor-xc-mini-find-bitting.html

CGDI MB Do All Keys Lost Programming for Benz W166
Posted by OBD scanner

Mercedes Benz W166 all keys lost and program new keys, CGDI MB Pro  is good choice, here share user manual with pictures.
 CG Pro 9S12
Guide:
Select Lock(EIS)
cgdi-mb-w166-all-keys-lost-01

Click on “Read EIS data” then “Computer password”
cgdi-mb-w166-all-keys-lost-02

Click on “Copy key without key” then “Collect Data”. CG100 Programmer
cgdi-mb-w166-all-keys-lost-03

Prepare to collect data, please wait…
cgdi-mb-w166-all-keys-lost-04

Please insert the simulation key into the lock in 30 seconds.
cgdi-mb-w166-all-keys-lost-05

CGDI MB programmer is collecting data.
cgdi-mb-w166-all-keys-lost-06 cgdi-mb-w166-all-keys-lost-07

Data acquisition succeed, save it by default.
cgdi-mb-w166-all-keys-lost-08

Click on “Upload data” then open the data you saved.
cgdi-mb-w166-all-keys-lost-09

Upload data successfully.
cgdi-mb-w166-all-keys-lost-09


Click on “Query password”
cgdi-mb-w166-all-keys-lost-11

Wait for 2 minutes, query password succeed.
cgdi-mb-w166-all-keys-lost-11

Click on “Lock (EIS)” then CGDI MB  display password, copy it.
cgdi-mb-w166-all-keys-lost-13

Click on “Paste password” http://handybaby.spruz.com/
cgdi-mb-w166-all-keys-lost-14  
Article from: http://blog.cgdishop.com/how-to-use-cgdi-mb-do-all-keys-lost-programming-for-benz-w166/

How to Perform BMW FEM/BDC Key Learning by CGDI BMW
Posted by OBD scanner

CGDI BMW   FEM BDC key learn  is in the dismantling method instead of OBD method. Then you have to know the FEM/BDC system location, 95128 IC location, 95256 IC location and Key learning position, read the detail in the below parts.
 CGDI Shop

  1. BMW FEM/ BDC installation location.

bmw-fem-bdc-key-learn-01
CGDI Benz Programmer

  1. 95128 IC location

bmw-fem-bdc-key-learn-02
 

  1. 95256 IC location

bmw-fem-bdc-key-learn-03

  1. Key learning position

bmw-fem-bdc-key-learn-04

That’s all.

Value bundle:
CGDI Prog BMW MSV80 plus BWM FEM/BDC Authorization .

Xhorse VVDI Prog, Xprog and R280 Read BMW cas4 5M48H
Posted by OBD scanner

Reading BMW cas4 5M48H, the optional working programmers are Xhorse VVDI Prog , Xprog 5.5 , Xprog 5.6 , Xprog 5.7 , R280 plus and Smok, etc.

Option 1: VVDI Pro read cas4 5M48H
Xhorse VVDI Pro can read and write 5M48H.
Here how to read 5M48H using Xhorse VVDI Prog .

Procedure:
Video demo: https://www.youtube.com/watch?v=ZWrQdha-OO8&feature=youtu.be
Open VVDI Pro software, select type, manufacture and model as MC9S12XEP100)
vvdi pro options-01
Click “Wiring Diagram”
Maximize wiring diagram: right click and select “zoom window”, then pull down window.
Follow the wiring diagram to connect CAS to the VVDI Pro.
wiring-diagram-02
Start to connect the cable. Car Key Programming Guide
connect-the-cable-03
The left zone is done, next is to do the right zone.
connect-the-cable-04
In this wiring diagram, it only need to remove one 0 ohm resistor to read out data, but one CAS ECU structure is different another one, some needs remove more electronic parts; we will show how to do in the other videos.
remove-one-0-ohm-resistor-05
Next is to remove this 0 ohm resistor.
remove-this-0-ohm-resistor-06
Wiring is done, 0 ohm resistor is removed
Finish-connecting-the-cable-07
Plug adapter into VVDI Pro.
Plug-adapter-into-VVDI-Pro-08
Close wiring diagram.

Select “New” – “ Read”
You see it is reading data very fast.
Reading data successfully, click “Save”
reading-data-successfully-09
Next is to check data.
Open the data, drag the mouse to check, okay, data is all read out, close it.

Option 2: XPROG-M V5.55, XPROG-M V5.70 and XPROG-M V5.60
Compared with XPROG-M lower version, XPROG-M V5.55, XPROG-M V5.70 and XPROG-M V5.60 add adaptor for 5M48H P-Flash, and already tested successfully by many ECU tunners.
xprog-m-v555-with-usb-dongle-new
Option 3: R280 Plus CAS4+ BDM programmer for MC9S12XEP100 chip (5M48H/1N35H)  
Top 5 features:

  1. R280 Plus, a powerful Motorola microcontroller dedicated programmer, supports the latest BMW Motorola MC9S12XEP100 chip (5M48H/1N35H).
  2. It supports automatically search mileage address and display the mileage
  3. Remove the chip, directly input the number of kilometers, the data is visible and can be arbitrarily edited, it allows user to arbitrarily read and write /P-FLASH D-FLASH data.

In a word, R280 plus features a powerful, decryption security, becoming the automotive computer repair, data recovery, data transfer and other professional electronic maintenance engineer.

  1. The latest generation of processor programmer.
  2. Using the latest software and hardware, hardware security level is high.


Powerful R280 Plus Update: Support for the upgrading of programming tools, to provide 24 hours of technical support, product 1 years warranty free upgrade.

Powerful R280 Plus microcontroller dedicated BMW Motorola programmer supports following models:
BMW 1 series – F20, F21 chassis – 2016 years ago
BMW X1 series – E84 chassis – 2016 years ago
BMW 3 series – F30, F31 and F35 chassis – 2016 years ago
BMW X3 series – F25 chassis – 2016 years ago
BMW 5 series – F10, F11 and F18 chassis – 2016 years ago
BMW X5 series...Read More

OBDSTAR H108 to Calibrate Citroen Cluster via OBD
Posted by OBD scanner

Used OBDSTAR H108  to do Citroen cluster calibration via OBD perfectly and easily, what I need to do is do what the screen display tells me to do.
  OBDSTAR X300M Mileage Programmer
Plug  OBDSTAR H108 to the Citroen BSI. OBDSTAR
obdstar-h108-citroen-cluster-calibration-01
Select"Cluster Calibrate".
obdstar-h108-citroen-cluster-calibration-02
Citroen
obdstar-h108-citroen-cluster-calibration-03 obdstar-h108-citroen-cluster-calibration-03 obdstar-h108-citroen-cluster-calibration-05
Select "BSI".
obdstar-h108-citroen-cluster-calibration-06
Auto select
obdstar-h108-citroen-cluster-calibration-07
If auto select failed, select "manual select".
obdstar-h108-citroen-cluster-calibration-08
Select "JC BSIO4EV-KOX".
obdstar-h108-citroen-cluster-calibration-09
Switch ignition on
obdstar-h108-citroen-cluster-calibration-10
Select "Read EEPROM".
obdstar-h108-citroen-cluster-calibration-11 obdstar-h108-citroen-cluster-calibration-12 obdstar-h108-citroen-cluster-calibration-13
Please enter a filename to save, press the "ENT" button.
obdstar-h108-citroen-cluster-calibration-14
Operation success
obdstar-h108-citroen-cluster-calibration-15
Press the "ENT".
obdstar-h108-citroen-cluster-calibration-16
Read Flash...
obdstar-h108-citroen-cluster-calibration-17
Press the "ENT" button.
obdstar-h108-citroen-cluster-calibration-17
Read Flash success.
obdstar-h108-citroen-cluster-calibration-19
Press "ENT".
obdstar-h108-citroen-cluster-calibration-20
Press "ENT".
obdstar-h108-citroen-cluster-calibration-21
Press "ENT".
obdstar-h108-citroen-cluster-calibration-22
Input a new value.
obdstar-h108-citroen-cluster-calibration-23 obdstar-h108-citroen-cluster-calibration-24
Success.
obdstar-h108-citroen-cluster-calibration-25 obdstar-h108-citroen-cluster-calibration-26
Done.
Perfectly, I am very happy with this OBDSTAR H108 , it doesn't let me down. I highly recommend it.
http://www.keycuttingmachine.org

SEC-E9 Key Cutting Machine cut Chevy DWO4 car key+ Schlage home key
Posted by OBD scanner

Do you want a key machine to cut both car key and home key? SEC-E9 Key Cutting Machine can do it! Check below to know how SEC-E9 cut Chevrolet DWO4 key and Schlage key for door lock! Condor XC-009

Part 1: How SEC-E9 cut Chevrolet/ Buick DW04 key blade?
Click the search button on main menu.
sec-e9-key-cutting-machine-cut-chevy-dw04-1
Enter “DWO4” then click search icon.
sec-e9-key-cutting-machine-cut-chevy-dw04-2
Choose “SILCA”→ “DWO4 (74) (8, 10)”
Choose correct space. In this case it is 8.
sec-e9-key-cutting-machine-cut-chevy-dw04-3 sec-e9-key-cutting-machine-cut-chevy-dw04-4
Click “Menu” then “Info” at bottom bar to get key blank information.
Click “Decode”, follow the screen guide, use stopper to put the original key correctly on clamp.
sec-e9-key-cutting-machine-cut-chevy-dw04-6 sec-e9-key-cutting-machine-cut-chevy-dw04-5
Click “Decode” to start decoding.
sec-e9-key-cutting-machine-cut-chevy-dw04-7
After that put the new Chevy DWO4R key blank on clamp, click “Cut” then set cutting speed.
Key cutting complete, test new key blank working!
sec-e9-key-cutting-machine-cut-chevy-dw04-8
Part 2: How to cut Schlage key by SEC-E9 CNC Automatic Key Cutting Machine?
Click “Standard” button on main menu.
sec-e9-key-cutting-machine-cut-schlage-home-key-1
Choose “Schlage” and “All Schlage”.
sec-e9-key-cutting-machine-cut-schlage-home-key-2
Select correct key model number and space.
sec-e9-key-cutting-machine-cut-schlage-home-key-3
sec-e9-key-cutting-machine-cut-schlage-home-key-4
Click “Decode” and pay attention to screen guide to fix the clamp correctly.
sec-e9-key-cutting-machine-cut-schlage-home-key-6 sec-e9-key-cutting-machine-cut-schlage-home-key-5
Put the original Schlage key to decode.
Then replace the new blank key blade to cut.
New Schlage key cutting finish!
sec-e9-key-cutting-machine-cut-schlage-home-key-7
sec-e9-key-cutting-machine-cut-schlage-home-key-8
Get SEC-E9 Key Cutting Machine $2,399 for car key and home key at uobdii.com!
http://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html

Article from Auto Key Cutting Machine blog

SEC-E9 Key Cutting Machine cut Chevy DWO4 car key+ Schlage home key
Posted by OBD scanner

Do you want a key machine to cut both car key and home key? SEC-E9 Key Cutting Machine can do it! Check below to know how SEC-E9 cut Chevrolet DWO4 key and Schlage key for door lock! Condor XC-009

Part 1: How SEC-E9 cut Chevrolet/ Buick DW04 key blade?
Click the search button on main menu.
sec-e9-key-cutting-machine-cut-chevy-dw04-1
Enter “DWO4” then click search icon.
sec-e9-key-cutting-machine-cut-chevy-dw04-2
Choose “SILCA”→ “DWO4 (74) (8, 10)”
Choose correct space. In this case it is 8.
sec-e9-key-cutting-machine-cut-chevy-dw04-3 sec-e9-key-cutting-machine-cut-chevy-dw04-4
Click “Menu” then “Info” at bottom bar to get key blank information.
Click “Decode”, follow the screen guide, use stopper to put the original key correctly on clamp.
sec-e9-key-cutting-machine-cut-chevy-dw04-6 sec-e9-key-cutting-machine-cut-chevy-dw04-5
Click “Decode” to start decoding.
sec-e9-key-cutting-machine-cut-chevy-dw04-7
After that put the new Chevy DWO4R key blank on clamp, click “Cut” then set cutting speed.
Key cutting complete, test new key blank working!
sec-e9-key-cutting-machine-cut-chevy-dw04-8
Part 2: How to cut Schlage key by SEC-E9 CNC Automatic Key Cutting Machine?
Click “Standard” button on main menu.
sec-e9-key-cutting-machine-cut-schlage-home-key-1
Choose “Schlage” and “All Schlage”.
sec-e9-key-cutting-machine-cut-schlage-home-key-2
Select correct key model number and space.
sec-e9-key-cutting-machine-cut-schlage-home-key-3
sec-e9-key-cutting-machine-cut-schlage-home-key-4
Click “Decode” and pay attention to screen guide to fix the clamp correctly.
sec-e9-key-cutting-machine-cut-schlage-home-key-6 sec-e9-key-cutting-machine-cut-schlage-home-key-5
Put the original Schlage key to decode.
Then replace the new blank key blade to cut.
New Schlage key cutting finish!
sec-e9-key-cutting-machine-cut-schlage-home-key-7
sec-e9-key-cutting-machine-cut-schlage-home-key-8
Get SEC-E9 Key Cutting Machine $2,399 for car key and home key at uobdii.com!
http://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html

Article from Auto Key Cutting Machine blog

Blog Categories
Recent Comments
"Where do we get real tech support and instructions?"
In: Xtool X100 Pad “Please input security code” (Solved)
by: Thinner
"I have a X-100 pad just bought it. It scans well however the key..."
In: Xtool X100 Pad “Please input security code” (Solved)
by: Thinner

This website is powered by Spruz