Blog Entries
How to fix Carprog Clone LIB File Problem
Category: General
Tags: carprog full carprog

Here is the working solution on Carprog clone “LIB file problem” by re-flashing Mcu ARM AT91SAM7S256 step by step.ECU Programmer

Problem:
Any work solution for carprog v8.21 clone?
“Lib file problem. delete LIB file and make Update>-Internet”
 


Solution:
Yes, reprogram ARM with any jtag programmer.

Reflash Carprog MCU ARM by Jtag:
We need the stuff:
1- AT91SAM7S256.bin
2- Jtag programmer
3- Jtag software
We need to prepare the Carprog to connect to Jtag programmer but first the flash need to be erased, the Jtag function in mcu is disabled, you can’t connect to the mcu before erase the flash. Remove the AT88SC eeprom from the board, please note where is the pin 1 in eeprom before remove:
 


Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it with a small amount of silicone (you don’t want to broke the pin in the process).
Connect the Carprog (with the pin 55 disconnected) to the 12v supply, wait about 10 seconds and connect the wire from pin 55 to Vcc (3.3V) in Carprog:

 



Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect the 12v supply from CarProg full  and remove the pin 55 wire from vcc. The pin 55 must remain disconnected until the programming process is done.
Ok, that’s it. I make it; and you try on you risk.
Article from:http://carprog-carprog.blogspot.com/2016/10/how-to-fix-carprog-clone-lib-file.html

How to Cut TOY43 Key using Condor XC-Mini Find Bitting
Category: General
Tags: Condor XC-Mini

OBD2 engineer  teach you how to use Xhorse Condor XC-Mini cut keys if parts of the car are missing bitting on door lock/trunk lock/ignition lock.

 SEC-E9 Key Cutting Machine
Step1: Select Car information
Connected to the power supply, open Condor XC-MINI
Enter main interface, Click on ‘Find Bitting’
xhorse-condor-xc-mini-find-bitting-1
Select car maker ‘’Toyota’ Key cutter Machine
xhorse-condor-xc-mini-find-bitting-2
Enter ’TOY43’ and click on ‘Confirm’
xhorse-condor-xc-mini-find-bitting-3
Select key type and click on ‘Confirm’
xhorse-condor-xc-mini-find-bitting-4
Enter known bitting ‘23112134’
Enter unknown bitting as ‘?’
xhorse-condor-xc-mini-find-bitting-5
(Possible key bitting will be listed. Note that system has sorted the codes by the most
economical way in order to save blank keys. For example, the bitting under ‘First key’ only
needs three blank keys, the bitting under “Second Key” need another three blank keys, then the ‘third Key’…)

Step2: Prepare Key
Then push M1 clamp and tighten the clamp lock
xhorse-condor-xc-mini-find-bitting-6
Next put the blank TOY43 key on the M1 clamp and tighten it
xhorse-condor-xc-mini-find-bitting-7
Close the protective shield

Step3: Begin cutting
Click on ‘Find Bitting Code’
xhorse-condor-xc-mini-find-bitting-8
And click on ‘Cut’
xhorse-condor-xc-mini-find-bitting-9
It is processing…
xhorse-condor-xc-mini-find-bitting-10
Cutting complete!
xhorse-condor-xc-mini-find-bitting-11
You can clean up the clamp, probe and the cutter using the brush.

Article from:http://chasencai.over-blog.com/2018/06/how-to-cut-toy43-key-using-condor-xc-mini-find-bitting.html

CGDI MB Do All Keys Lost Programming for Benz W166
Category: General
Tags: CGDI MB

Mercedes Benz W166 all keys lost and program new keys, CGDI MB Pro is good choice, here share user manual with pictures.
 CG Pro 9S12
Guide:
Select Lock(EIS)
cgdi-mb-w166-all-keys-lost-01

Click on “Read EIS data” then “Computer password”
cgdi-mb-w166-all-keys-lost-02

Click on “Copy key without key” then “Collect Data”.CG100 Programmer
cgdi-mb-w166-all-keys-lost-03

Prepare to collect data, please wait…
cgdi-mb-w166-all-keys-lost-04

Please insert the simulation key into the lock in 30 seconds.
cgdi-mb-w166-all-keys-lost-05

CGDI MB programmer is collecting data.
cgdi-mb-w166-all-keys-lost-06 cgdi-mb-w166-all-keys-lost-07

Data acquisition succeed, save it by default.
cgdi-mb-w166-all-keys-lost-08

Click on “Upload data” then open the data you saved.
cgdi-mb-w166-all-keys-lost-09

Upload data successfully.
cgdi-mb-w166-all-keys-lost-09


Click on “Query password”
cgdi-mb-w166-all-keys-lost-11

Wait for 2 minutes, query password succeed.
cgdi-mb-w166-all-keys-lost-11

Click on “Lock (EIS)” then CGDI MB display password, copy it.
cgdi-mb-w166-all-keys-lost-13

Click on “Paste password”http://handybaby.spruz.com/
cgdi-mb-w166-all-keys-lost-14 
Article from:http://blog.cgdishop.com/how-to-use-cgdi-mb-do-all-keys-lost-programming-for-benz-w166/

How to Perform BMW FEM/BDC Key Learning by CGDI BMW
Category: General
Tags: CGDI BMW

CGDI BMW FEM BDC key learn is in the dismantling method instead of OBD method. Then you have to know the FEM/BDC system location, 95128 IC location, 95256 IC location and Key learning position, read the detail in the below parts.
 CGDI Shop

  1. BMW FEM/ BDC installation location.

bmw-fem-bdc-key-learn-01
CGDI Benz Programmer

  1. 95128 IC location

bmw-fem-bdc-key-learn-02
 

  1. 95256 IC location

bmw-fem-bdc-key-learn-03

  1. Key learning position

bmw-fem-bdc-key-learn-04

That’s all.

Value bundle:
CGDI Prog BMW MSV80 plus BWM FEM/BDC Authorization.

Xhorse VVDI Prog, Xprog and R280 Read BMW cas4 5M48H
Category: General
Tags: VVDI2 VVDI Prog

Reading BMW cas4 5M48H, the optional working programmers are Xhorse VVDI Prog, Xprog 5.5, Xprog 5.6, Xprog 5.7, R280 plus and Smok, etc.

Option 1: VVDI Pro read cas4 5M48H
Xhorse VVDI Pro can read and write 5M48H.
Here how to read 5M48H using Xhorse VVDI Prog.

Procedure:
Video demo: https://www.youtube.com/watch?v=ZWrQdha-OO8&feature=youtu.be
Open VVDI Pro software, select type, manufacture and model as MC9S12XEP100)
vvdi pro options-01
Click “Wiring Diagram”
Maximize wiring diagram: right click and select “zoom window”, then pull down window.
Follow the wiring diagram to connect CAS to the VVDI Pro.
wiring-diagram-02
Start to connect the cable.Car Key Programming Guide
connect-the-cable-03
The left zone is done, next is to do the right zone.
connect-the-cable-04
In this wiring diagram, it only need to remove one 0 ohm resistor to read out data, but one CAS ECU structure is different another one, some needs remove more electronic parts; we will show how to do in the other videos.
remove-one-0-ohm-resistor-05
Next is to remove this 0 ohm resistor.
remove-this-0-ohm-resistor-06
Wiring is done, 0 ohm resistor is removed
Finish-connecting-the-cable-07
Plug adapter into VVDI Pro.
Plug-adapter-into-VVDI-Pro-08
Close wiring diagram.

Select “New” – “ Read”
You see it is reading data very fast.
Reading data successfully, click “Save”
reading-data-successfully-09
Next is to check data.
Open the data, drag the mouse to check, okay, data is all read out, close it.

Option 2: XPROG-M V5.55, XPROG-M V5.70 and XPROG-M V5.60
Compared with XPROG-M lower version, XPROG-M V5.55, XPROG-M V5.70 and XPROG-M V5.60 add adaptor for 5M48H P-Flash, and already tested successfully by many ECU tunners.
xprog-m-v555-with-usb-dongle-new
Option 3: R280 Plus CAS4+ BDM programmer for MC9S12XEP100 chip (5M48H/1N35H) 
Top 5 features:

  1. R280 Plus, a powerful Motorola microcontroller dedicated programmer, supports the latest BMW Motorola MC9S12XEP100 chip (5M48H/1N35H).
  2. It supports automatically search mileage address and display the mileage
  3. Remove the chip, directly input the number of kilometers, the data is visible and can be arbitrarily edited, it allows user to arbitrarily read and write /P-FLASH D-FLASH data.

In a word, R280 plus features a powerful, decryption security, becoming the automotive computer repair, data recovery, data transfer and other professional electronic maintenance engineer.

  1. The latest generation of processor programmer.
  2. Using the latest software and hardware, hardware security level is high.


Powerful R280 Plus Update: Support for the upgrading of programming tools, to provide 24 hours of technical support, product 1 years warranty free upgrade.

Powerful R280 Plus microcontroller dedicated BMW Motorola programmer supports following models:
BMW 1 series – F20, F21 chassis – 2016 years ago
BMW X1 series – E84 chassis – 2016 years ago
BMW 3 series – F30, F31 and F35 chassis – 2016 years ago
BMW X3 series – F25 chassis – 2016 years ago
BMW 5 series – F10, F11 and F18 chassis – 2016 years ago
BMW X5 series – F15 chassis – 2016 years ago
BMW 6 series – DMEM/F12 F13 chassis – 2016 years ago
BMW X6 series – F16 chassis – 2016 years ago
BMW 7 series – F01, F02, F03, F04 chassis – 2016 years ago
BMW GT series – F07 chassis – 2016 years ago
BMW CAS and CAS4 (0K50E/2K79X/0L01Y/0L15Y/1L15Y, etc.).
BMW EWS4 (2L86D).
EZS (1J35D/2J74Y/4J74Y/0L02M/1L02M/3K85K/3K91D/1L85D/1L59W/3L40K/4L40K, etc.).
Support for a variety of SRS computers
(9H91F/0K13J/0K75F/0L85D/0J38M/1E62H/1K79X/5H55W, etc.).
Support M35080 series quick wipe, read and write (35080/35080-V6/35080-VP/080D0WQ/160D0WQ/35160, etc.).
FLASH 0K50E online write.

Have an overview on R280 Plus Software Display:
r280-plus-cas4-10 r280-plus-cas4-7 r280-plus-cas4-6 r280-mcu type r280 ic select r280 ic select-02 r280 d flash read

OBDSTAR H108 to Calibrate Citroen Cluster via OBD
Category: General
Tags: OBDSTAR H108

Used OBDSTAR H108 to do Citroen cluster calibration via OBD perfectly and easily, what I need to do is do what the screen display tells me to do.
 OBDSTAR X300M Mileage Programmer
Plug OBDSTAR H108 to the Citroen BSI. OBDSTAR
obdstar-h108-citroen-cluster-calibration-01
Select"Cluster Calibrate".
obdstar-h108-citroen-cluster-calibration-02
Citroen
obdstar-h108-citroen-cluster-calibration-03 obdstar-h108-citroen-cluster-calibration-03 obdstar-h108-citroen-cluster-calibration-05
Select "BSI".
obdstar-h108-citroen-cluster-calibration-06
Auto select
obdstar-h108-citroen-cluster-calibration-07
If auto select failed, select "manual select".
obdstar-h108-citroen-cluster-calibration-08
Select "JC BSIO4EV-KOX".
obdstar-h108-citroen-cluster-calibration-09
Switch ignition on
obdstar-h108-citroen-cluster-calibration-10
Select "Read EEPROM".
obdstar-h108-citroen-cluster-calibration-11 obdstar-h108-citroen-cluster-calibration-12 obdstar-h108-citroen-cluster-calibration-13
Please enter a filename to save, press the "ENT" button.
obdstar-h108-citroen-cluster-calibration-14
Operation success
obdstar-h108-citroen-cluster-calibration-15
Press the "ENT".
obdstar-h108-citroen-cluster-calibration-16
Read Flash...
obdstar-h108-citroen-cluster-calibration-17
Press the "ENT" button.
obdstar-h108-citroen-cluster-calibration-17
Read Flash success.
obdstar-h108-citroen-cluster-calibration-19
Press "ENT".
obdstar-h108-citroen-cluster-calibration-20
Press "ENT".
obdstar-h108-citroen-cluster-calibration-21
Press "ENT".
obdstar-h108-citroen-cluster-calibration-22
Input a new value.
obdstar-h108-citroen-cluster-calibration-23 obdstar-h108-citroen-cluster-calibration-24
Success.
obdstar-h108-citroen-cluster-calibration-25 obdstar-h108-citroen-cluster-calibration-26
Done.
Perfectly, I am very happy with this OBDSTAR H108, it doesn't let me down. I highly recommend it.
http://www.keycuttingmachine.org

SEC-E9 Key Cutting Machine cut Chevy DWO4 car key+ Schlage home key
Category: General
Tags: SEC-E9

Do you want a key machine to cut both car key and home key? SEC-E9 Key Cutting Machine can do it! Check below to know how SEC-E9 cut Chevrolet DWO4 key and Schlage key for door lock! Condor XC-009

Part 1: How SEC-E9 cut Chevrolet/ Buick DW04 key blade?
Click the search button on main menu.
sec-e9-key-cutting-machine-cut-chevy-dw04-1
Enter “DWO4” then click search icon.
sec-e9-key-cutting-machine-cut-chevy-dw04-2
Choose “SILCA”→ “DWO4 (74) (8, 10)”
Choose correct space. In this case it is 8.
sec-e9-key-cutting-machine-cut-chevy-dw04-3 sec-e9-key-cutting-machine-cut-chevy-dw04-4
Click “Menu” then “Info” at bottom bar to get key blank information.
Click “Decode”, follow the screen guide, use stopper to put the original key correctly on clamp.
sec-e9-key-cutting-machine-cut-chevy-dw04-6 sec-e9-key-cutting-machine-cut-chevy-dw04-5
Click “Decode” to start decoding.
sec-e9-key-cutting-machine-cut-chevy-dw04-7
After that put the new Chevy DWO4R key blank on clamp, click “Cut” then set cutting speed.
Key cutting complete, test new key blank working!
sec-e9-key-cutting-machine-cut-chevy-dw04-8
Part 2: How to cut Schlage key by SEC-E9 CNC Automatic Key Cutting Machine?
Click “Standard” button on main menu.
sec-e9-key-cutting-machine-cut-schlage-home-key-1
Choose “Schlage” and “All Schlage”.
sec-e9-key-cutting-machine-cut-schlage-home-key-2
Select correct key model number and space.
sec-e9-key-cutting-machine-cut-schlage-home-key-3
sec-e9-key-cutting-machine-cut-schlage-home-key-4
Click “Decode” and pay attention to screen guide to fix the clamp correctly.
sec-e9-key-cutting-machine-cut-schlage-home-key-6 sec-e9-key-cutting-machine-cut-schlage-home-key-5
Put the original Schlage key to decode.
Then replace the new blank key blade to cut.
New Schlage key cutting finish!
sec-e9-key-cutting-machine-cut-schlage-home-key-7
sec-e9-key-cutting-machine-cut-schlage-home-key-8
Get SEC-E9 Key Cutting Machine $2,399 for car key and home key at uobdii.com!
http://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html

Article from Auto Key Cutting Machine blog

SEC-E9 Key Cutting Machine cut Chevy DWO4 car key+ Schlage home key
Category: General
Tags: SEC-E9

Do you want a key machine to cut both car key and home key? SEC-E9 Key Cutting Machine can do it! Check below to know how SEC-E9 cut Chevrolet DWO4 key and Schlage key for door lock! Condor XC-009

Part 1: How SEC-E9 cut Chevrolet/ Buick DW04 key blade?
Click the search button on main menu.
sec-e9-key-cutting-machine-cut-chevy-dw04-1
Enter “DWO4” then click search icon.
sec-e9-key-cutting-machine-cut-chevy-dw04-2
Choose “SILCA”→ “DWO4 (74) (8, 10)”
Choose correct space. In this case it is 8.
sec-e9-key-cutting-machine-cut-chevy-dw04-3 sec-e9-key-cutting-machine-cut-chevy-dw04-4
Click “Menu” then “Info” at bottom bar to get key blank information.
Click “Decode”, follow the screen guide, use stopper to put the original key correctly on clamp.
sec-e9-key-cutting-machine-cut-chevy-dw04-6 sec-e9-key-cutting-machine-cut-chevy-dw04-5
Click “Decode” to start decoding.
sec-e9-key-cutting-machine-cut-chevy-dw04-7
After that put the new Chevy DWO4R key blank on clamp, click “Cut” then set cutting speed.
Key cutting complete, test new key blank working!
sec-e9-key-cutting-machine-cut-chevy-dw04-8
Part 2: How to cut Schlage key by SEC-E9 CNC Automatic Key Cutting Machine?
Click “Standard” button on main menu.
sec-e9-key-cutting-machine-cut-schlage-home-key-1
Choose “Schlage” and “All Schlage”.
sec-e9-key-cutting-machine-cut-schlage-home-key-2
Select correct key model number and space.
sec-e9-key-cutting-machine-cut-schlage-home-key-3
sec-e9-key-cutting-machine-cut-schlage-home-key-4
Click “Decode” and pay attention to screen guide to fix the clamp correctly.
sec-e9-key-cutting-machine-cut-schlage-home-key-6 sec-e9-key-cutting-machine-cut-schlage-home-key-5
Put the original Schlage key to decode.
Then replace the new blank key blade to cut.
New Schlage key cutting finish!
sec-e9-key-cutting-machine-cut-schlage-home-key-7
sec-e9-key-cutting-machine-cut-schlage-home-key-8
Get SEC-E9 Key Cutting Machine $2,399 for car key and home key at uobdii.com!
http://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html

Article from Auto Key Cutting Machine blog

how to use OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32
Category: General

Recently,OBDSTAR engineer share video guide on how to use OBDSTAR H100 program dealer key for VW Polo 2013 NEC 24C32.Here OBDSTAR share it for customers.

Procedures:
Connect OBDSTEAR H110 to vehicle by OBD port.
Power on the device.
Select “VEHICLE”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (1)
Select “IMMOBILISER”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (2)
Select”VW/AUDI/SKODA/SEAT”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (3)
Select “VW/ADUI/SKODA/SEAT V33.25”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (4)
Select “VW”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (5)
Read security code
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (6)
4 Generation Immo
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (7)
NEC+24C32 ICM
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (8)
Make Ordinary Dealer Key.
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (9)
Reading data …
Please connect RFID with diagnostic device
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (10)
Please put the new key in RFID adapter.
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (11) OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (12)

Reading data …
Generating dealer key…
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (13)
When you find the LED light on the RFID adapter flash on 3 time,the OBDSTAR H110 Programmer will prompt you “Make Dealer key success”
OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32 (14)

Attention Please:
If you find the warning massage with “Communication Breakdown”.Please check below conditions:
1.Ignition Switch is turned on
2.Mainline is connected
3.Battery has power
4.Is Equipped with this ….
OBDSTAR X300 DP PAD Programmer
From OBDSTAR Tools Technical Official Blog, post OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32

CGDI BMW program key on BMW CAS4 /CAS 4+ all key lost
Category: General
Tags: CGDI BMW program key on BMW CAS4 /CAS 4+ all key lost

Have BMW MSV80 and looking for a key programmer to add new key for BMW CAS1/CAS2/CAS3/CAS3+ and match key for CAS4 /CAS 4+ when all key lost, you must use CGDI Prog BMW MSV80 key programmer.
cgdi-pro-bmw-msv80-key-programmer-1

Attach one table which show CGDI Prog functions, workable models and working time
cgdi-pro-workable list-01

As you can see, CGDI Prog BMW MSV80 key programmer has these capabilities:

  1. 1.BMW CAS1/CAS2/CAS3/CAS3+/key increasing matching, KEY all lost matching, CAS computer replace,CAS3+/P4X above version can directly downgrade by OBD in 5 minus 100% safety.

2.BMW CAS4/CAS4+/Support key matching, support key all lost matching.
3.Support BMW key inspection, can check key what status in.
4.Support BMW engine computer DME replacement.
5.Support BMW MSV80/MSD80/MSD85/series OBD read ISN code (no need to split computer when matching key) Exclusively support in Domestic
6.Support BMW Key unlock.

Moreover, CGDI Prog can perform:
1.Update in real time, products updated in zero cycle time, support model added in real time.
2.BMW CAS3/CAS3+Data repair–support change replace and split CAS computer, BMW MSV80/MSV80.0/MSD80/MSD80.0/MSD85/engine change computer, ISN code reading and writing.
3.Equipment security greatly enhanced, the hardware anti-crack, anti-software copy.

CGDI MB Benz

How to use CGDI Prog BMW MSV80 key programmer?
Method 1: can directly read ISN code in the car, please ensure the car voltage is 12V and above, it directly connects OBD to operate, takes about 5 minus.
Method 2: can directly disassemble engine computer (DME) to operate, follow the below guide to connect the line:
cgdi-pro-bmw-msv80-key-programmer-1
cgdi-pro-bmw-msv80-key-programmer-pic-4 
CGDI Shop

Yanhua Mini ACDP Programmer Function List
Category: General
Tags: Yanhua Mini ACDP

Recently,Yanhua released their newest programmer Yanhua Mini ACDP Programmer.It will save a lot of time for auto locksmith,because you don't need to soldering/welding when you use Mini ACDP to perform key programming or mileage correction for BMW.
 



Yanhua Mini ACDP Programmer Function List:
1. Memory programming:
Support 93/24/25/35/95 series EEPROM in circuit (ICP)and on board(OBP)programming and parts of Freescale/ NEC MCU in circuit programming(ICP).

2. BMW module programming:
(1) Support cas1-cas4+and FEM/BDC IMMO key programming, mileage reset, program recovery.
(2)BMW engine ECU data reading and ISN code reading

3. VW module programming. MMC instrument
4. Instrument mileage and airbag ECU reset/maintenance is under development.
5. BENZ. BMW Audi and various models are upgraded successively

Yanhua Mini ACDP Programmer:
http://www.uobdii.com/wholesale/yanhua-mini-acdp-programming-master.html

Xhorse VVDI2, VVDI Prog, VVDI MB tool Reviews
Category: General
Tags: VVDI Key Tool VVDI2

Xhorse electronics vvdi reviews here, incl xhorse the best:
VVDI mercedes review
VVDI Prog programmer review
VVDI2 programmer review
CGDIShop

VVDI MB Tool review

– cost-effective and powerful
vvdi mb can renew elv without soldering the nec while the other should sold out and not make via obd2, vvdi mb can renew EIS no need token even its bga eis , while others cannot , with small budget can program bga key with 6 minutes while with others you need 5 thousands dollars to do , more over for w204 all key lost no body in the world can do it while they are working on it with vvdi
xhorse-vvdi-mb-bga-tool-new-1
– 204 all keys lost ok
For 204 all keys lost one solution is to buy eis with key tested and ok

– W203 password calculation via IR
I read pass W203 IR OK

– W203 W220 read password ok
W203: EIS/EZS A203.545.05.08 – MCU ??? -read PSW IR – OK
W203: EIS/EZS A203.545.05.08 – MCU 1J35D – read PSW – OK
W220: EIS/EZS A215.545.02.08 – MCU ??? -read PSW IR – OK
– support older ESL
old ESL(motorola) are supported read through K-line yet……look in ESL menu, there are some possibility…

for me are all older ESL from 202, 203, 208,209,201,211 and so…then when in the adapter are socket for the 28-pin HC05E6 motorola, then are this supported too…
the emulator is too for all this OLD type of ESL…

– renew this namber 7G tronic 003 446 0310
Can renew this namber 7G tronic 003 446 0310
i have renewed 10 pcs of this part number, all success

– made a key to W203
I have made a key for W203.
Works great but the remote controle opens only the drivers door.

– Exchange W204 ESL without renew EIS
Exchange W204 ESL without renew EIS. In ESL Tools, write EIS with password(Select Auto clear TP and personalized) tested and work ok

– w204 w207 w212 all key lost work
All key lost:
W204 work
W207 work
W212 work


VVDI Prog Review

– read/write Fiat 9s12dg256b mcu without problem
Yesterday i read/write mcu 9s12dg256b from fiat bcm with vvdi Prog WITHOUT Problem
vvdi-prog-1
VVDI Prog secured very well
I work’s on opel astra h cim with hc912 mcu,
ford dashboard hc912, and with hc908az60
secured very well.

– 080dowq erasing works perfect
Now I tried 080dowq erasing, and it works perfect.

– R/W ok with CIM Opel Astra H
3L40K – Read ID (0113) ok, Rean EEP (ok) Read Flash (ok)
1L59W- Read ID (0115) ok, Read EEP (NOT) Read Flash (NOT).

Ps. 3L40K – Just that flash is smaller than It should be.
Read-it with smok, and You will understand what I am saying.

– 50/50 chance to Porsche BCM
I have tried to read Porsche BCM with 9S12 5M48H dated 2013 MCU but could not do it because VVDI Prog did not detected chip ID. Always get ID: FFFF
While Porsche BCM with MCU 9S12 2M25J dated 2014 have read without problems

– 209 flash ok
I received the vvdi prog and tested eis
209 with st12 eeprom flash ok

– vvdi prog read ok with W221
for w221 ism with ST10F269 read by vvdi prog OK with micromax diagram
for write it didn’t erase automatically you have to erase it before, then all OK .

–  ok with D70F3571
vvdi prog 4.5.1 D70F3571 read ok

– no issues with BSI 307 2002
BSI 307 2002 912DG128 – 3K91D
EEP (read and write) – OK
FLASh 4.000Mhz (read and write) -OK — Orange5 clone (DO NOT write flash)
Identical files Vvdi prog and Orange5, same EEP and FLASH.
Incircuit BSI photo of Orange5.

– vvdiprog + eeprom adapter without issues
works fine with eeprom adapter
does not work with test clip tried to different ones,
maybe i should try other one, if there is any higher quality,
or maybe because of cable length it doesnot work

– good at EZS, CAS2, CAS3, CAS3+ …
this programmer can read write EZS, cas2, cas3, cas3+, read other motorolas safe without any problems or damages

– work OK on BMW CAS4 F10 2014
Today tested: CAS4 with Motorola 1N35H mask from F10 2014!
d/p-flash BACKUP – ok
Crack chip security – ok
read/write p/d-flash – ok
Locked – ok
Works without heating the chip. Only removed 4 elements from the board, and after operations resoldered them back.
i have desoldered 4 elements from the board: transistor, capacitator, resistor and cristal/quartz.


– vvdi prog not working?:
– VVDI PROG CANNOT READ 68HC805 FOR IMMO MAZDA 323

– It cannot read hcx05 at all.

– Cannot support read pin code for psa and old chrysler



Xhorse VVDI2 review

VVDI2 BMW:

– CAS1 bmw read eeprom by obd
i did yesterday CAS1 bmw read eeprom by obd and got key info and cutting code
vvdi2-key-programmer-1
– bmw ews direct by obd
vvdi2 bmw can make key in bmw ews direct by obd or need read ews dump by programmer then make key

– program new keys to bmw e90 2008 USA
i have a vvdi2 with vag and bmw authroization
have to programmed new keys in bmw (bmw e90 2008 USA year), without keyless go
in original key inside transponder pcf7953 315mhz
My hint for you: Chinese keys work only transponder but remote need to remove cas and do it on bench on tango or xhorse vvdi, but obd method need always original for better chance chip is 7945 or 7953 which is 46 family good luck

– support MED17/EDC17 dump tool
Xhorse vvdi2 v1.2.1 adds support for MED17/EDC17 dump tool, support clone ECU(Menu->Special Function->MED17/EDC17 dump tool)
But sadly only work for Condor key cutting machine users
my vvdi 2 is full not basic.but function for edc17 only for condor cutter user.no for all vvdi2 full user
vvdi mb bga have the token system, if you have condor cutter 1 token in 1 day for free if you don’t have you need pay
it is different


VVDI2 AUDI:

– do Control head on A6
Vvdi2 able to do Control head on A6
need Transponder Sokymat Crypto 8E – Audi ID8E precoded by Component Security.
If you want to add remote key: 4F0837220AK, 4F0837220R, 4F0 837 220 – and others.

– key learn for Audi A4 RB8 crypto (2004+)
VVDI2 key learn procedure for Audi A4 RB8 crypto (2004+) option:
Just read the pin and cs from ecu.
Make backup from cluster, and the cluster configuration.
Then make a dealer key, and learn it with pin.

Audi A7 2012 km done
Audi A7 2012 km done by reading config by obd then read eeprom by Programmer ——– ok!

– Audi S8 spare key job done
Did one Audi S8 done successfully, spare key job

– add keys to AUdi a4 2009 BCM2
AUdi a4 2009 BCM2 key added successfully in 2 minuts.

Audi Q5 add keys, read bcm2
I did Audi Q5 add key ok, read BCM2 by OBD ok, read BCM2 by bdm ok.
Passat B6 all key lost by eep ok.

Audi A3 8P 434 not working
Remote programmer test remote for Audi A3 8P 434, not working.
Not file for Golf 5 434.
Test remote generator Ibiza 6J “1k0 …. N” 434 working.

Audi A4 2008 not working
VAG remote key adaptation does not connect to many old cars but usually works fine with newer “dealer keys”. However, Audi A4 2008 did not connect to car (BCM or BFM). Key programming ok.
On a side note: A4 2008 do not have BCM, models 2009 + has BCM.


VVDI 2 & others:

– Peugeot 308 2008 BSI JC pin extracted
Peugeot 308 2008 BSI JC pin extracted OK. Key learn failed – first key OK, second key failed. Tried several times. Job finished with other device.

Passat B6 read code and add keys
Passat B6 read Code from confort module (95320) & added key ok!

– 0D69J file identified
BENZ a class 0D69J file identified ok, but write transponder not work

– Passat B7 failed
Passat B7 Read Code from confort (95320) & add key by obd ——— Failed, (i made by transponder tool option)
VVDI Key Tool

RSS

Blog Categories
Recent Comments
"Where do we get real tech support and instructions?"
In: Xtool X100 Pad “Please input security code” (Solved)
by: Thinner
"I have a X-100 pad just bought it. It scans well however the key..."
In: Xtool X100 Pad “Please input security code” (Solved)
by: Thinner

This website is powered by Spruz